Speed Queen washer error codes are your washer’s way of letting you know something isn’t working as it should.
This guide makes Speed Queen washer error codes easy to understand so you can spot the issue quickly. When you need expert Speed Queen washer repair, our professional Speed Queen technicians are ready to assist.
What Causes Speed Queen Washer Error Codes
Your washer shows error codes when it runs into a problem. Here are the most common reasons:
- Water isn’t flowing into the washer properly
- The door or lid doesn’t lock or unlock like it should
- Water won’t drain out because of a clog
- The washer can’t spin because of a motor or belt issue
- The washer’s brain (control system) is having trouble
These Speed Queen washer error codes point you toward the source of the problem so you can better understand what’s happening.
How to Fix the Most Common Speed Queen Washer Error Codes
Basic Tools for Visual Checks
You don’t need special tools, but these can help you take a quick look:
- A flashlight to see inside or under the washer
- A towel or bucket in case water leaks
- A screwdriver to remove a small panel if needed
- Your washer’s manual for guidance
Now, let’s go through each Speed Queen washer error code and what you can do.
Reset the Washer
Resetting your washer is often the first thing to try:
- Unplug it for 1 to 3 minutes for most home models
- Unplug for 5 minutes for bigger or commercial washers
- Plug it back in and start a new cycle
If the error comes back, move on to some simple checks you can do yourself.
Common Speed Queen Washer Error Codes
FL – Fill Error
The washer isn’t filling with water.
- Make sure both faucets are turned on
- Check if the hoses are kinked or bent
- Look at the screens where hoses connect for dirt
dL – Door Lock Error
The washer won’t start because the door can’t lock.
- Close the door firmly
- Make sure nothing is stuck in the latch
- Let your technician know if it still won’t lock
dU – Door Unlock Error
The door won’t open after washing.
- Wait a few minutes to see if it unlocks
- Gently try opening the door
- Tell your technician if it stays locked
DR / ND – Drain Error
Water won’t drain out of the washer.
- See if water is sitting in the bottom
- Clean the drain filter (see your manual)
- Listen for any buzzing without water draining
ER – Communication Error
Parts of the washer aren’t communicating properly.
- Unplug the washer, wait, and plug it in again
- If it happens again, call for help
SR – Spin Error
The washer isn’t spinning like it should.
- Spread clothes out evenly inside the drum
- Restart the cycle
- If it made loud sounds before stopping, tell your technician
LE – Lid Switch Error
The washer thinks the lid isn’t closed.
- Push the lid down firmly
- Look for clothes stuck around the edges
- This switch may need replacing if it keeps happening
UE – Unbalanced Load
The washer shakes or won’t spin.
- Move the clothes around evenly
- Don’t wash one heavy item by itself
- Make sure the washer is sitting level on the floor
PF – Power Failure
The washer lost power during a cycle.
- Check that it’s plugged in
- Look at your circuit breaker
- Start the cycle again if power is back
NF – No Fill Detected
The washer doesn’t know water is coming in.
- Check that the water is turned on
- If hoses look fine, the sensor may need checking
Less Common but Important Error Codes
Some codes might not appear often, but they signal important issues:
- OF (Overflow/Suds): Too much soap or water inside the washer
- E1 – Door Lock Issue: The washer doesn’t think the door is locked
- E5 – Pressure Switch Problem: The washer can’t tell how much water is in it
- E7 – Heater Circuit Error: The heating part isn’t working
- Ed22 – Motor Overheated: The motor got too hot
- El Codes – Leak Detected: The washer found a leak
If any of these show up, write down the code and what was happening.
Frequently Asked Questions
How do I enter diagnostic mode?
On many Speed Queen washers, hold “Soil Level” and “Spin” while turning the washer on. Check your manual to be sure.
Can one issue cause more than one error code?
Yes. If the water sensor fails, you might see NF and OF at the same time.
Does my washer keep a record of error codes?
Yes, most models do. A technician can look them up during service.
Which codes can I usually fix myself?
FL, PF, and UE are common. They usually involve water, power, or load balance and often don’t need new parts.
Bonus Tip
Run a monthly maintenance cycle with hot water and a washer cleaner. This helps prevent buildup that can trigger error codes like OF (suds/overflow) or drain-related issues.
Need dependable Speed Queen washer repair? Call Solar Appliance Service. Our technicians provide fast, reliable solutions to keep your washer running smoothly.
